In Proxmox VE, the Qemu-guest-agent is used for mainly two things: It is used to exchange information between the host and guest, and to execute command in the guest. NOTE-2: Do not use default /usr/local as it is the place where the package system installs the software.The Qemu-guest-agent is a helper daemon, which is installed in the guest. NOTE: You need to use 'gmake', not plain 'make'. pixmap is now of of the submodules, so no need to install it either. Gcc and binutils are in the base distribution so no need to install them. Of course this is not mandatory and you can use whatever size you prefer as long as it's bigger than 10GB.įor installation instructions you can follow this guide, section "Long Walkthrough of DragonFly BSD Installation and Configuration",Īlthough it might not be completely accurate it is a good one: Configuration ![]() # echo '=ufs:vbd0s2a' > /boot/nfĭepending on whether you're going to use UFS or HAMMER you are encouraged to use a specific HDD size since HAMMER works better with +50GB disks. The Regents of the University of California. To set a device for booting permanently on the USB image: There is a way to make this permanent which is explained below. Note: You will likely find this error while booting. drive if=virtio,file=DragonFly-x86_64-LATEST-IMG.img,format=raw \ No need to create a disk image as the USB image itself will act as the raw image disk file for qemu: At the moment of this writing latest stable version is 4.8.1. One is to use the USB image to boot from it directly, as a raw image, the other one is to use the ISO and install dfly onįetch either daily snapshot or the release ISO/image files, links below. Pkg_add git gmake python37 glib2 bison pkgconf pixmanĭragonFly BSD Resources for the installation You should now be able to get in to the VM with Edit /etc/ssh/sshd_config to set 'PermitRootLogin: without-password', and set up ssh authorized keys. When it gets to the big menu of things to configure at the end of the install: configure networking (select defaults) enable NTP and ntpdate enable ssh set a root password. Optional dependencies if you want to run the test frameworkĬreate a disk image, and grab the install cd image: (This is necessary because QEMU assumes it can map memory RWX for TCG and 'make check' will fail if it can't.) Then either reboot or use "mount -uo wxallowed /wherever" to set it for this session. Ssh sure that the filesystem you're building and running QEMU from has the "wxallowed" option set in /etc/fstab, like:ĭ3651b0622794af6.k /home ffs rw,wxallowed,nodev,nosuid 1 2 Ssh-copy-id should now be able to get in to the VM with Reboot when it asks, and when it's rebooted kill the QEMU VM.Ĭopy your ssh public key into root's. To fix this and add the SMP kernel after the initial install enter 'boot hd0a:bsd.rd' at the bootloader prompt to re-run the installer and add the 'bsd.mp' layer. NB: it's important to run the installer with more than one CPU, or it will not install the SMP kernel. You'll want to enable sshd and allow logins with prohibit-password. netdev user,id=mynet0,hostfwd=tcp:127.0.0.1:7922-:22 \įollow the straightforward install prompts (accepting defaults generally OK). drive if=virtio,file=disk.qcow2,format=qcow2 \ (NB as of you'll also need -disable-user to work around a QEMU bug.) Note that you need to use 'gmake', not plain 'make'. You can configure and build QEMU as you would on Linux: Pkg install bash capstone4 gsed curl nettle png usbredir devel/sdl20 It is also recommended to install these packages for additional features and testing: Pkg install git gcc gmake python pkgconf pixman bison glib You should now be able to ssh into the VM from outside with (TODO: check virtio works and recommend that instead.)Įnable networking and ssh by adding these lines to /etc/rc.conf:Ĭopy your ssh public key into the VM's /root/.ssh/authorized_keys If you're running natively on BSD you can ignore the "VM setup" instructions.ĭownload and uncompress the official FreeBSD qcow2 image from ![]() This page includes documentation of how to get the various BSD flavours running in a VM inside QEMU, so that Linux-based developers can do build tests on them. ![]() At the moment most QEMU developers are Linux users, though, so BSD is not very well supported. This documentation is not written by a BSD expert - corrections welcome!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |